Uncategorized

Fluffernutter Sammie Stout Update

Fluffernutter Sammie Stout, out of the fermentation chamber briefly to ease the temp up a bit.

Fluffernutter Sammie Stout, out of the fermentation chamber briefly to ease the temp up a bit.

Update 5/24/2016: An unexpected little run of cooler temperatures had me worried that the beer was not fermenting. I know it did for a couple of days, albeit a bit slowly…never really started “chugging”, but going. Then the cool weather, and my little fermentation chamber is outside. It is only able to cool, not warm, so this could be a problem. Since the overnight low last night was going into the mid to lower 50’s, I decided to bring the carboy inside.

I took a sample and did a temperature and hydrometer reading. The temp was 62.5, so it wasn’t terrible…a little under optimum range, but should not be low enough to have caused any harm. The hydrometer has the specific gravity at 1.030, so it definitely was fermenting. That’s good! Adjusting for the lactose, I think it will likely only go to 1.028 or so.

Hydrometer sample for evaluation...specific gravity, temperature and flavor.

Hydrometer sample for evaluation…specific gravity, temperature and flavor.

The flavor of the sample has my hopes up! The color may be a tad light, but it’s a little darker than the sample shows, because of the camera flash and the particles had not settled out yet. I could definitely taste the peanut flavor, especially in the finish. Nice malty sweetness. After the sample chilled overnight, the peanut flavor is more muted. With that and the consensus from others that the peanut flavor will start fading after a couple of months in the bottles, I do plan to add more peanut powder to secondary via boiling it with water and cooling it…probably a gallon and then racking onto it and the vanilla beans. I’m going to skip the marshmallow Fluff in secondary and rely on the vanilla for that flavor, so I’m not adding much more fermentable sugars. I may try adding some to the boil in a future batch, but not this time. I have a feeling that this beer’s flavor will improve as it loses some of its chill, after pouring.

The temperature on the carboy strip thermometer reads around 66-68F, so I’ll be putting it back in the fermentation chamber later today.

Advertisements
Standard
Uncategorized

Day 154 Brew Day! Scottish Samhain Pumpkin Ale

Samhain label...no artist to credit, but it's beautiful!    Not for sale, so I guess it's okay.

Samhain label…no artist to credit, but it’s beautiful! Not for sale, so I guess it’s okay.

After I picked up a new oxygen canister and some bags of ice, I set up for brewing my Scottish Pumpkin Ale that I’m calling “Samhain”, which is the Celtic version of Halloween and is pronounced “so-win”.

The recipe is a modification of a Scottish Ale recipe from a member at www.Homebrewtalk.com. I put the recipe together like this (but note the changes as I brewed!):

Scottish Samhain Pumpkin Ale

Original Gravity: 1.068 Final Gravity: 1.019 ABV (standard): 6.49%

IBU (tinseth): 30.47 SRM (morey): 19.58

Fermentables

Amount Fermentable PPG °L Bill %

14 lb United Kingdom – Maris Otter Pale 38 3.75 73.7%

1 lb American – Caramel / Crystal 80L 33 80 5.3%

0.75 lb United Kingdom – Brown 32 65 3.9%

4 oz Molasses 36 80 1.3%

3 lb Dry Malt Extract – Light 42 4 15.8%***

19 lb Total

Hops

Amount Variety Type AA Use Time IBU

1 oz East Kent Goldings Pellet 5 Boil 60 min 19.79

0.5 oz Fuggles Pellet 4.5 Boil 60 min 8.91

0.5 oz Fuggles Pellet 4.5 Boil 5 min 1.78

Hops Summary

Amount Variety Type

1 oz East Kent Goldings Pellet 5

1 oz Fuggles Pellet 4.5

Mash Guidelines

Amount Description Type Temp Time

5.5 gal BIAB Infusion 158 F 60 min

2 gal modified sparge Fly Sparge 168 F —

Other Ingredients

Amount Name Type Use Time

29 oz Pumpkin, canned, roasted 30 minutes at 425F,  Boil 15 min

29 oz Pumpkin, canned, roasted Other Secondary 0 min

2 tbsp Pumpkin Pie Spice Spice Boil 0 min

1 each Vanilla Bean, split Flavor Secondary —

2 oz Vodka, to soak vanilla bean Other Secondary —

Yeast

White Labs – Edinburgh Scottish Ale Yeast WLP028

Attenuation (avg): 72.5% Flocculation: Medium

Optimum Temp: 65 – 70 °F Starter: Yes

Fermentation Temp: 70 °F Pitch Rate: 1.25 (M cells / ml / ° P)

393 B cells required (Guess…I have no experience calculating this.)

Priming

Method: Corn Sugar CO2 Level: 2.4 Volumes

Target Water Profile: Cary Town Water

Method: BIAB

Style: Holiday/Winter Special Spiced Beer

Boil Time: 60 min

Batch Size: 5 gallons (fermentor volume)

Boil Size: 7.5 gallons

Boil Gravity: 1.045 (recipe based estimate)

Efficiency: 35% (brew house)*** 

Source: Matt Miller

Non-grain fermentables added at 60 minutes.

Irish Moss added at 15 minutes.

 

***So, there were a couple of issues that required some changes. The efficiency that was the default in the recipe builder for Brew in a Bag (BIAB) brewing was 34%  and I evidently get double that.

Sparging...kind of.

Sparging…kind of.

Set up for a rigged "sparge". Seems to do the job.

Set up for a rigged “sparge”. Seems to do the job.

After the mash, I had an SG of 1.075, which was already better than projected and I had not yet added the 3 lbs of DME I thought I would need to add to the boil…so I omitted it entirely.

The process went smoothly. If anyone is interested, there are other posts that go through the process. The color is really nice!

Nice color!

Nice color!

Sorry the photos aren’t better…*someone* took my camera to use at a Demi Lovato concert and didn’t bring it back in time. I had to use my phone’s camera. I did chill the wort down to 76F, using an ice bath.

Ice bath chill

Ice bath chill

Then I pulled a sample, oxygenated the wort for 2 minutes using a sanitized oxygen canister and “oxygen stone” set-up and pitched my Edinburgh Ale Yeast (that I harvested from a previous batch of cider). I had prepared a starter for the yeast in advance and it was very active. I don’t have experience with “pitch rates”, but I believe I have plenty of yeast cells for the job. Since the volume I wound up with is about 6 gallons, in a standard fermentation bucket, and I have seen this yeast ferment very aggressively, I went ahead and set up a blow-off tube  to keep from fouling the airlock.  The yeast was pitched around 5:10 pm. As of 9:45 pm, I’m hearing a little action in the blow-off tube.

Blow-off tube.

Blow-off tube.

Now, aside from the process, let’s talk about the sights, smells, and flavors! I made my own pumpkin pie spice blend, using cinnamon, cloves, ginger and nutmeg. I did freshly grate the nutmeg. Also, the ginger has been around along time, so I supplemented it with a little grated fresh ginger. I roasted a can of Libby’s Pumpkin, spread on some parchment paper, on a baking sheet, at 425F for about 30 minutes. It wasn’t particularly pretty, but it picked up a few dark spots from caramelization and lost a lot of water. I kept the pumpkin in a sanitized storage container until I was ready for it.

Roasted, canned pumpkin

Roasted, canned pumpkin

The wort took on a great brown color with a dark orange-ish shade to it. Really nice! And the aroma and flavor from the pumpkin and spices are very good, too. I think this is going to be a VERY good beer.

Using the hydrometer sample, the OG came in at 1.083 and, if the attenuation rate is accurate, the ABV will be 7.91%; however, in my experience, the SG isn’t going to stop at 1.023…so, the ABV will likely be over 8%. And, this sample was also the basis for the flavor and color evaluations.

Hydrometer sample...settling a little.

Hydrometer sample…settling a little.

An update on the ciders and muscadine wine: the wine is basically bulk aging and clearing nicely. I’ll eventually rack it…maybe a couple more weeks, and let it go a few months, before I bottle it. The Caramel Cider made with crab apples and Cripps apples is pretty much bulk, aging as well. It did have a little airlock activity going on for a while after racking…not regular or often, though. It has almost stopped now, I think, so I’ll probably rack that a final time in about a week. Maybe bottling in two weeks. The crab apple, pear and Cripps apples cider…no name for it yet…is still bubbling pretty regularly in the airlock. It probably won’t be bottled for a month.

I think I’m learning that it pays to take a little extra time. Excess sediment in the bottom of bottles seems to be messing with my carbonation after bottles have been around for a couple of months. And I like my ciders to have very good clarity…not as huge a deal for all beers, but some. (For instance, wheat beers are actually supposed to be a little hazy.) So, slow down…get it right. Give it another week. It can only help!

Update: 9/15/14  Getting very good action in the blow-off on the Samhain Pumpkin Ale. It hasn’t fouled and it isn’t quite what I have heard some describe as “Rhino farts”, but it is almost constant bubbling.

Update:  9/15/14  Opened the test bottle of the caramel cider to see what it’s doing. No carb at all. The ABV is a hefty 10.89%, though and the flavor is nice. Color is good. Finished product will be more clear.  Alcohol may have pushed the Edinburgh Ale yeast past its tolerance…may have to explore options, if I want to carb.

Caramel Cider tester bottle...no carb; lots of alcohol.

Caramel Cider tester bottle…no carb; lots of alcohol.

Standard