Uncategorized

Brew Day! Yooper’s Oatmeal Stout

"The Con"

“The Con”

I prepared yesterday by purchasing my ingredients, getting my propane tank refilled, and buying 7 bags of ice.  The first thing I did was activate the “smack pack” of yeast that I used in this batch. It’s recommended to do so, 3 hours in advance of pitching. I’m brewing Yooper’s Oatmeal Stout, a recipe highly rated by several brewers and created by a brewer and moderator at the Home Brew Talk website. The recipe can be found at:   http://www.homebrewtalk.com/f68/yoopers-oatmeal-stout-210376/

The yeast is Wyeast British Ale II (#1335) and my batch is dated Dec 10th, so it’s very fresh!

Wyeast British Ale II (#1335)

Wyeast British Ale II (#1335)

It is supposed to supply 100 billion cells. The next step was setting up “The Con”. Basically, a table, a chair, the propane, burner, strike water and all the supplies/equipment…and a cup of coffee.

My local home brew supply shop was able to pretty closely duplicate the ingredients for me. I used 10 oz of Thomas Faucette Pale Chocolate Malt in place of the “Crisp”, Bairds 70-80L for the Caramel/Crystal Malt 80L, and Breiss for the 350 SRM Chocolate Malt. I also upped my Maris Otter to 8 lbs to satisfy my recipe builder program’s efficiency number estimate. (Brewer’s Friend) One other thing: I split my hops into 1 oz at 60 minutes and 1 oz at 30 minutes. Brewer’s friend estimated the IBU’s would be too high if I did 2 oz at 60 minutes.

For the process, I used the Brew in a Bag (BIAB) method that I have be doing since early last Spring. I heated my water to 159F and added my grains. I stirred to break up all the dry balls. My poor long plastic spoon needs to be replaced by a mash paddle! (Santa?) I turned off the burner and wrapped the pot with a blanket and a “space blanket” to try to maintain the temperature.

Wrapped for temperature retention.

Wrapped for temperature retention.

After 15 minutes, I checked the temperature and it had dropped to 154F. I gave the mash a burner boost, but overshot it up to 162F…rats!

Steeping grains, BIAB.

Steeping grains, BIAB.

I stirred constantly for a few minutes, but the temp wasn’t dropping very fast, so I added approx. 24oz of cold Culligan bottled water. I had the mash temp back down to just above the target 156F with 25 minutes to go in the mash. I wrapped it all back up again and it finished right on target. I hope the variation didn’t hurt too much.

I “tea bag” dunked & drained the grains a couple of times.

Tea bag dunk and drain.

Tea bag dunk and drain.

I also do a “modified sparge” that I have pictured in my journal before…I missed taking a photo this time. Basically, it’s a bottling bucket and tubing set up on a tall recycle container and I drain the water, in this case 1 gallon water at 167F, over the grains. The idea is to rinse additional sugars from the grains. Then I made sure the grains were well drained and squeezed out as best as I could, without burning myself. (I later added the grains to my compost container…I still have some in the freezer for making doggie treats.)

I checked the pre-boil specific gravity with my refractometer and it was 1.041…on target. I transferred the wort to the bottling bucket to measure the volume. It was right to the rim, which is 7 gallons.

measuring the pre-boil wort in a bottling bucket.

measuring the pre-boil wort in a bottling bucket.

I poured the wort back into the brew pot and re-lit the burner.

IMG_20141221_133516678

The boil was good…added 1oz of Willamette hops pellets at 60 minutes got a vigorous boil going.

IMG_20141221_141450364

I missed my 30 minute hop (also 1oz Willamette )addition by 5 minutes, but it shouldn’t be a big deal. Post boil SG was 1.066 amd the volume looked a little low, so I added 1/2 gallon cold Culligan bottled water and immersed the brew pot into an ice water bath.

Ice water bath to chill.

Ice water bath to chill.

I used 6 bags of ice and managed to get the temperature down to 72F in less than 25 minutes. A copper coiled wort chiller would be nice, though. (Uh…Santa?!) I checked the OG with both a hydrometer and refractometer. The hydrometer sample was 69F and the reading was 1.055. The refractometer was 1.056. After correcting the hydrometer reading for the sample temperature, the readings agreed at 1.056. I transferred the wort to a bottling bucket for primary fermentation and aerated it with oxygen for two minutes…

Hydrometer sample and oxygen stone aerator.

Hydrometer sample and oxygen stone aerator.

…and then pitched the yeast and sealed the lid.  The volume in the bucket appears to be about 6-1/2 gallons and is close enough to the top that I decided to go ahead and set up a blow-off tube, just in case. Now we wait for the yeast to start partying! According to the estimates, I’m almost dead-on the numbers. I should finish within about .05 of the ABV percentage projection.

Wort aerated and yeast pitched.

Wort aerated and yeast pitched.

When primary fermentation is done, I plan to split the wort and use 2 gallons to make a gingerbread version. Need to research those additions. I do plan to include some freshly grated ginger root. It really made a difference in my Scottish Samhain Pumpkin Ale, evidently. I had some guys at the local home brew shop taste it and the one I think has the most experience picked up on it right away. I assume the other componants will be ground ginger, ground cinnamon, vanilla (bean or extract?) … maybe some molasses? Not too much, though. It is fermentable and I found that a small amount really made a nice difference in a cider that I did earlier this year. Okay…updates as needed to follow!

Update: As of the next morning, there was no noticable activity. I sanitized around the lid and opened just enough that I heard some fizziness. I resealed the lid. By a few hours later, I could hear a regular chugging in the overflow liquid. So…things are good!

 

 

 

Advertisements
Standard
Uncategorized

Day 133 Brew Day! Citra Saison with Harvested Yeast Starter

Setting up for brewing

Setting up for brewing

This was an uncharacteristic brew day for me. I usually don’t brew on weekdays. Certainly not Mondays. But the starter I had hoped to pitch in a Citra Saison pushed me back a day. I have never harvested yeast and never made a starter before now and I was afraid that the starter was going to be too weak. I worked out a boost for the starter (see previous post) and moved the brew back a day.

After I got everything all set up and ready to go, I got my BIAB (Brew In A Bag) in place and heated my strike water, 6 gallons.  The goal was 150F…water went to 154F and I mashed in. The water only dropped 1/2 degree though. I turned off the heat and made a run for ice. When I returned, the temp was 150.2F. Over the next 45 minutes, I tried my best to maintain the target temperature of 150F; however, it was probably more consistently in the 153F range.

After the BIAB (Boil In A Bag) steep and "sparge"

After the BIAB (Boil In A Bag) steep and “sparge”

Here is where I will talk about my changes to the original recipe that I found online. First of all, I decided to do Pale Malt 2 row, instead of Pilsner. Two reasons: sale on Pale and 60 minute boil instead of 90 minute. (Some recommend Pilsner boil for 90 to reduce chance of off flavors.) Next, I added 1 teaspoon of Irish Moss at 15 minutes left in the boil to aid clarity. I also realized that I had forgotten to buy 1 pound of Belgian Clear Candi Syrup…made a run to the closest brew shop, only to find that they are closed on Mondays. Aaaargh! So, I substituted a pound of raw North Carolina honey, instead (at 10 minutes left in the boil). I am also planning on adding a dry hop step to secondary. The recipe calls for Citra hops to be added 1/2 oz at 30 minutes and 1/2 oz at 10 minutes left in the boil. I am a big Citra fan, so I am going to add an ounce in secondary.

Okay, back to the procedures: After the 1 hour mash in, I did my usual “tea bag” style dunking and draining of the bag, using a large pizza screen over the pot for support. I then set up a bottling bucket with 2 gallons of sparge water at about 150F and used the spigot with some hose on it to do an improvised sparge. I’ve used this method that, as far as I know, I made up, a few times and I think it helps a little. This left me with a rather full kettle, so the boil was a challenge and had to be monitored pretty carefully.

The pizza screen was helpful in the tea bag style sparging and in helping keep bugs and debris out.

The pizza screen was helpful in the tea bag style sparging and in helping keep bugs and debris out.

I set timers for my additions and all of that went well. Did my usual ice bath chill and managed to get the temperature of the wort down to about 90F, pretty quickly…good temperature for Belle Saison yeast.

Now, I wanted to use my glass carboy for primary fermentation, so I could have a visual on activity. The problem is getting 7 gallons of wort from a stock pot into a heavy glass 6 gallon carboy using a funnel. I struggled and spilled a bit, trying to figure out a grip and pouring into a small target that filled quickly. I could see that wasn’t going to cut it, so I poured about 3/4 of the wort into the bottling bucket I had used for the sparging, and then went through the spigot and hose into the carboy. Obviously, I was going to have too much wort, so, rather than toss it, I grabbed and sanitized a one gallon carboy and put the rest of the wort into it.

I used my oxygen tank to oxygenate the big carboy for two minutes and the little one for one minute. Between the refractometer reading of 1.048 and the hydrometer reading, corrected for temperature to 1.044, I’m  going to estimate 1.046 OG.* Rather than try to decant my yeast starter, I decided to swirl the flask to mix it well and pitch the whole thing…guesstimating some for the smaller batch. The starter wort used pale DME (Dry Malt Extract), so it shouldn’t hurt the flavor of the beer. The recipe doesn’t give a projected FG, but Belle Saison is pretty aggressive, so I’m betting on around 1.002 for the big batch. So, maybe a 5.78% ABV? I would be happy with that.

Here's the volume of wort I wound up with.

Here’s the volume of wort I wound up with and my flask of starter yeast.

I have no clue what to expect for the one gallon batch, because I’m going to add one pound of fresh cherries to secondary fermentation, rather than dry hopping it, and the sugar in the cherries will surely kick fermentation back into gear. I currently have the whole cherries in the freezer with some vodka. When it comes time to rack the small batch, I’ll crush the cherries into the vodka a little to release some juice and add it all. I’ll probably use a 2 gallon bucket that I use for ciders to do the small batch secondary, so I have a wide opening with which to work.

The recipe calls for a week each for both primary and secondary; however, my Hi-Nelson Saison needed a little over two weeks for primary and then a week for secondary. And the small batch may go longer in secondary. I’ll probably even rack the small batch to a tertiary stage to clarify once it’s off the fruit. Probably back into a glass carboy again so I can judge the clarity.

The big question mark is whether my yeast starter was going to work. The yeast was pitched at 3:15 p.m. and the carboys were set on a heating pad, on the lowest setting. At 6:30, there was no activity evident and the glass felt pretty cool.

Carboys on the heating pad.

Carboys on the heating pad. (Beside some Hi-Nelson Saison with Hibiscus and some Diet Root Beer (Truvia)

I upped the heating pad to medium and wrapped the carboys in a “Space Blanket”. By 9:30 p.m., they were both chugging along in the airlocks…not violently, but good, frequent bubbles every second or two. Success!!! Woo hoo!!!

Heating pad AND Space Blanket...now we're chugging!

Heating pad AND Space Blanket…now we’re chugging!

I cold crashed the hydrometer sample just to see what it looks like and how it tastes at this stage. Obviously malty and sweet at this point, but it seems like it will be nice and clean, light bitterness and the hops should shine through on the main batch and the Belle Saison should add a little spice and funk. The little cherry batch should be really interesting!

Hydrometer sample, cold crashed and easier to get a read. And a taste for evaluation.

Hydrometer sample, cold crashed and easier to get a read. And a taste for evaluation.

*I also let this sample come to room temperature and took another hydrometer reading. at 74.2F and 1.046, adjusted to 1.047, so that will be my new OG to go with. I read the hydrometer with no contacts or glasses and it was much easier to get a good read, so I feel confident with that figure. (An additional refractometer reading, of course, calls it 1.048, so…whatever!) Could be around 6% ABV…anywhere in that  5.75 to 6.05% range is close enough.

For the original version of the recipe, go to this link or cut and paste into your browser:

http://www.danielshomebrew.blogspot.com/2014/01/citra-saison.html

Always give credit where due!

Update: Okay…the following morning, the airlocks were fouled. I quickly set up blow offs and the yeast is going at it, big time! Definitely had enough yeast!

 

Standard